Contact Angle Of Water Droplet Research Articles

Preparation of Hydrophobic Au Catalyst and Application in One-Step Oxidative Esterification of Methacrolein to Methyl Methacrylate.

The water produced during the oxidative esterification reaction occupies the active sites and reduces the activity of the catalyst. In order to reduce the influence of water on the reaction system, a hydrophobic catalyst was prepared for the one-step oxidative esterification of methylacrolein (MAL) and methanol. The catalyst was synthesized by loading the active component Au onto ZnO using the deposition-precipitation method, followed by constructing the silicon shell on Au/ZnO using tetraethoxysilane (TEOS) to introduce hydrophobic groups. Trimethylchlorosilane (TMCS) was used as a hydrophobic modification reagent to prepare hydrophobic catalysts, which exhibited a water droplet contact angle of 111.2°. At a temperature of 80 °C, the hydrophobic catalyst achieved a high MMA selectivity of over 95%. The samples were characterized using XRD, N2 adsorption, ICP, SEM, TEM, UV-vis, FT-IR, XPS, and water droplet contact angle measurements. Kinetic analysis revealed an activation energy of 22.44 kJ/mol for the hydrophobic catalyst.

Multifunctional carbon nanotubes coated stainless steel mesh for electrowetting, hydrophobic, and dye absorption behavior

Electrowetting behaviour for carbon nanotubes (CNT) grown on stainless steel mesh was investigated. The effect of temperature, time, and applied bias voltage on the contact angle of water droplets was studied. The impact of temperature variation on contact angle was also performed for the temperature ranging from 25 to 70 °C. A decrement of contact angle by 68% was observed for the mentioned range indicating a transition from a hydrophobic to hydrophilic nature. A similar trend was observed on the application of electric potential to the CNT-modified stainless-steel mesh ranging from 0 to 8 V with a transition of contact angle from 146 to 30 deg respectively. A comparative analysis for the contact angle variation with time for CNT-coated mesh and uncoated mesh was performed for 180 min. It is observed that uncoated mesh shows a reduction in contact angle to 0 deg with time while the CNT coated mesh shows surplus hydrophobicity with a 2 deg decrement in the extent of time. CNT-modified mesh successfully absorbs 95% of rhodamine B (RB) dye and detergent from water in 10 cycles.

Cellulose nanofiber as mask/personal protective equipment surface agent for enhanced anti-bacterial performance

The utilization of face-covering masks as an extended form of personal protective equipment has led to exponential waste measures during the COVID-19 pandemic, with estimations of up to 7200 tons of medical-type waste daily. A primary cause of this waste is surgical layered disposable masks that are constructed by melt-blown nonwovens usually made of non-biodegradable thermoplastic polymers like polypropylene. To increase widespread sustainable options to the public, commercialized or do-it-yourself-based fabric masks serve as a solution, but their resistance to harmful molecules is less than that of the medical-grade masks due to the fabric structure that leaves space for penetration. This project examines a water-soluble dispersion composed of cellulose nanofiber and polyvinyl alcohol, as a spray agent capable of treating the mask fabric surface to promote protection and sustainability against harmful aerosol particles. Cellulose nanofiber spray is also low-cost and biocompatible and could allow multi-use through home laundering. Polyvinyl alcohol was chosen as the water-soluble bonding system and polymer matrix to effectively adhere cellulose nanofiber onto the mask surface. This project follows the biomimic concept of dragonfly wings having uneven nanopillar surfaces to trap and rip bacterial membranes, as the spray decreases the water droplet contact angle on fabric surface, resulting in an increase in adhesion for incident bacteria and/or viruses.

Preparation of super-hydrophobic BN nanotube mesh and theoretical research of wetting state

In this study, we have fabricated stainless steel mesh with columnar super-hydrophobic boron nitride nanotubes (BNNTs) through the ‘gas-liquid-solid’ mechanism annealing method. We employed iron (Fe) powder as the catalyst and utilized boron (B) and boron oxide (B2O3) as the raw materials. The synthesis took place within a tubular furnace, operating under an NH3 atmosphere at a temperature of 1250C∘. The contact angle of water droplets on the experimental surface measures approximately 150∘, while the sliding angle is approximately 3∘. In the next place, the laboratory carried out a series of experiments on the tensile properties, corrosion resistance, and erosion resistance of the prepared samples. The experimental results showed that the sample material had good mechanical properties and corrosion resistance. In addition, the erosion resistance test results showed that the sample material even at high speed (2800 rpm/min). After washing the sample for 5 min, the surface of the material still has good wettability (contact angle is 136.49∘). Finally, droplet bouncing experiments have demonstrated that the adhesion force on the surface of the boron nitride nanotube stainless steel mesh is notably minimal, indicating its substantial hydrophobic properties. Additionally, we conducted an investigation into the wetting interaction between droplets and the surface of the boron nitride nanotube stainless steel mesh. By applying the Wenzel and Cassie formulas and considering the pertinent geometric parameters of the material surface, we theoretically elucidated that, upon contact, the droplets assume a ‘Cassie’ state on the surface of the super-hydrophobic boron nitride nanotube stainless steel mesh. The research results show that the superhydrophobic boron nitride nanotube stainless steel mesh has broad application prospects in the fields of hydrogen storage, sewage treatment and oil-water separation.

Cotton fabrics modified with tannic acid/1-eicosanamine grafting layer for oil/water separation

The wettability of the surface of hydrophilic cotton fabrics was modified using a one-step protocol with tannic acid (TA) to provide its excess catechol groups to be grafted with 1-eicosanamine at pH 8.5 and room temperature with catalysts CuSO4/H2O2. The modification over the synthesis conditions revised the contact angles of water and diiodomethane droplets from 132.68 ± 0.49° to 143.95 ± 0.80° and from 100.08°±1.42° to 82.96 ± 1.38°, respectively. The corresponding dispersive of the so-yielded cotton surface ranged from 8.6 to 16.0 mJ/m2, and the polar components ranged from 0.08 to 2.7 mJ/m2, much lower than polytetrafluoroethylene. The modified cotton fabrics are omniphobic and can repel water and commercial oil products. The absorption tests revealed that the modified cotton fabrics absorbed 1.10 g hexane/g cotton by contacting hexane (top)-water (bottom) layers and absorbed 1.26 g hexane/g cotton by contacting water first for 30 s, then hexane for another 30 s. The modified fabrics reveal good absorption reusability as hexane absorbent is even pre-saturated with water. This conclusion is also valid for commercial unleaded gasoline #95 and diesel. A parametric study revealed that the added catalysts and prolonged reaction time would enhance the hydrophobicity of the surface. These modified cotton fabrics can absorb oil from water and oil spills. Mechanisms corresponding to this observation are discussed.

Extraction and characterization of cellulose microfibers from cornhusk for application as reinforcing agent in biocomposite

This study aims to extract and characterize cellulose microfibers from cornhusk, an agricultural by-product. The extracted fibers will then be used as a reinforcing agent in a biocomposite made of thermoplastic corn starch. The process of extracting cellulose microfibers involved two treatments: sequential alkali treatment (using sodium hydroxide at 120 °C for 120 min) and peroxide bleach treatment (using hydrogen peroxide at 90 °C for 60 min). Various techniques such as Fourier transform infrared (FTIR), X-Ray diffraction (XRD), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA) were employed to characterize the extracted fibers. The properties of the composite were examined through tensile strength tests, contact angle measurements, and UV–Vis spectrophotometry. The study found that cellulose microfibers were successfully extracted from cornhusks, with a diameter of 7 to 30 μm and a crystallinity of 65 %. The treated fibers showed gradual degradation between 150 °C and 350 °C, indicating a lower amount of non-cellulosic substances compared to untreated cornhusks. Adding 10 % of the microfibers to the thermoplastic starch composite increased the tensile stress at breaking and the Young's modulus, but decreased the contact angle of water droplets and the film's transparency.

Effects of ultrasound combined with hydrothermal treatment on the quality of brown rice

In order to improve the rough mouthfeel of brown rice, the effects of ultrasound (U) combined with hydrothermal (H) treatment on texture, sensory score and cooking quality of brown rice were studied, and the improvement mechanism was revealed from the aspects of room temperature water absorption, water droplet contact angle, microstructure and starch ordered structures. The results showed that ultrasound hydrothermal treatment cycle (UH-UH) can significantly improve the eating quality of brown rice. After UH-UH, the hardness, chewiness, optimal cooking time and volume expansion rate all reached to the level of white rice, and the stickiness significantly increased from 0.126 N of the control to 1.114 N. The sensory score of cooked brown rice rose from 57.37 to 76.70. On the other hand, room temperature water absorption rate far exceeded that of white rice, and the water droplet contact angle and relative crystallinity decreased significantly. In addition, scanning electron microscopy found that the cracks and micropores on the surface of treated brown rice grains increased greatly, which may be the underlying reasons for the improvement in the eating quality of brown rice. This study helps to provide a new way for producing high-quality brown rice.

The design and performance research of PTFE/PVDF/PDMS superhydrophobic radiative cooling composite coating with high infrared emissivity

High infrared emissivity in the atmospheric transparent spectral band, high reflectivity in the solar radiation band, self-cleaning and no heat treatment process are crucial for the application of the radiative cooling materials. In this work, a superhydrophobic radiative cooling composite coating was facilely prepared by using two sizes of polytetrafluoroethylene (PTFE) particles as main fillers and silica (SiO2) nanoparticles as auxiliary fillers, and polydimethylsiloxane (PDMS) and polyvinylidene fluoride (PVDF) as binders. The coating can be scraped onto the substrate through a scraper without any heat treatment procedure. The water droplet contact angle (WCA) and rolling angle (SA) of the coating can reach a maximum of 158 ± 0.5° and a minimum of 3 ± 0.3°, respectively. The average reflectance of the coating in the visible spectral band was around 90.6%. The average infrared emissivity of the coating in 8 ∼ 13 µm spectral band was about 0.989. The test results show that the coating has excellent self-cleaning and cooling properties. Furthermore, the coating also exhibits good abrasion resistance, preferable adhesion performance, ultraviolet radiation resistance, high temperature stability, self-cleaning and anti-icing performance.

Performance Evaluation of a Multifunctional Road Marking Coating for Tunnels Based on Nano SiO2 and TiO2 Modifications

Multifunctional road marking coatings with the functions of high-temperature stability, degradation of exhaust gas, and self-cleaning are of great significance for the safe operation and environmental protection of tunnels. This article uses active acrylic resin and an organosilicon hydrophobic agent as the base material, selects expanded vermiculite and glass microspheres as insulation fillers, and uses ammonium polyphosphate, pentaerythritol, melamine, and aluminum hydroxide as high-thermal-stability systems to prepare a two-component road marking coating base material. Then, nano SiO2 and modified nano TiO2 are added as modifiers to prepare a multifunctional road marking coating for tunnels. The physical and chemical properties of multifunctional road marking coatings are evaluating based on laboratory tests including thermogravimetry and derivative thermogravimetry, differential scanning calorimetry, infrared spectroscopy, scanning electron microscopy, exhaust degradation, and contact angle tests. The results indicate that the developed multifunctional road marking coating effectively reduces the thermal conductivity of the carbon layer through physical changes in the flame retardant system and the heat resistance formed by the high breaking bond energy of nano SiO2 during the combustion process. It forms a ceramic-like structure of titanium pyrophosphate with nano TiO2 that is beneficial for improving flame retardancy without generating harmful volatile gases and has good flame retardant properties. N–V co-doping reduces the bandgap of TiO2, broadens the absorption range of visible light by nano TiO2, improves the catalytic efficiency of visible light, and achieves the degradation efficiency of the four harmful components NOx, HC, CO, and CO2 in automotive exhaust by 23.4%, 8.3%, 2.5%, and 2.9%, respectively. The solid–liquid phase separation in the multifunctional road marking coating in the tunnel causes the formation and accumulation of nano SiO2 and TiO2 particles on the coating surface, resulting in a microstructure similar to the “micro–nano micro-convex” on the lotus leaf surface and making a water droplet contact angle of 134.2° on the coating surface.

Impact of argon dielectric barrier discharge cold plasma on the physicochemical and cooking properties of lightly-milled rice

This study investigated the influence of argon dielectric barrier discharge-cold plasma (DBD-CP) applied at different voltage settings (1 kV and 2 kV) and exposure durations (5 min and 10 min) on the physicochemical properties, cooking behavior, textural attributes, and flavor characteristics of lightly-milled-rice (LMR). The DBD-CP treatment increased the brightness of untreated LMR from 62.93 to 76.69, and reduced the water droplet contact angle from 66.66° to 58.99° following a treatment of 2 kV-10 min. Moreover, the treatment enhanced the crystallinity and gelatinization enthalpy of LMR starch by 8.93% and 60.55%, respectively. Conversely, it led to a decrease in the amylose content by 7.66% when compared to the control group. Metabolomic analysis revealed a decrease in the content of key compounds involved in metabolic pathways, including amino acids, α-hydroxy acids, and GABA. The cooking experiment demonstrated a substantial reduction by 5.4 min in optimal cooking time, along with water absorption capacity and volume expansion rate increased by 54.19% and 68.42% in 2 kV-10 min DBD-treated LMR, respectively. Notably, DBD-CP treatment positively influenced the production of important aroma compounds such as alcohols, aldehydes, and ketones. Overall, DBD-CP proved to be an effective physical processing method for significantly enhancing the edible quality and aroma of LMR.

Chemically bound hydrophobic modification in hydrogel surface layer using poly(N-vinylamide)s

The novel hydrophobic surface modification of hydrogel structure, referred to as organohydrogel, was firstly achieved through the utilization of poly(N-vinylamide)s hydrogels, taking advantage of the property of polycation precursor. Following the shrinkage of poly(N-acetamide-co-N-vinylformamide), only the surface moiety was subjected to hydrolysis. Subsequently, a radical initiator was chemically tethered to the amino groups on the hydrogel surface to facilitate atom transfer radical polymerization (ATRP) of hydrophobic monomer, phenylethylacrylate. Hydrophobic layer characteristics were differentiated by varying hydrolysis time (xt) and ATRP time (yt), resulting in the creation of hydrophobic surface-modified gel (HSMgel). All HSMgels resulted in stable swelling ratio (S.R.) regardless of yt. The contact angle of water droplets increased gradually with both increasing xt and yt, from 17.6° to 91.9°, while maintaining a relatively constant S.R. The drying process of hydrophobic surface-modified HSMgels was accelerated, while that of precursor hydrophilic gels was delayed. These unique properties stemmed from the chemical structure of poly(N-vinylamide)s, which led to the formation of a chemically bound hydrophobic layer within the hydrogels.

Changes in the hydrophilicity of the surface of PADC under ionizing radiations: Anomalous increase of the contact angle of water droplets under protons

The contact angle of water droplets decreases above certain absorbed doses in the case of heavy ions (He, C and Kr ions). Similarly, monotonic decreases are seen due to exposures to corona discharge and UV lights. The present trends indicate that the hydrophilicity of PADC surface increases by the contribution of hydroxyl groups.In comparison, the contact angle increases due to proton irradiations up to 1.3×105 Gy. Then it begins to decrease monotonically with increasing the absorbed dose. The present anomalous trend is discussed based on the combination of the track overlapping model and the Young’s formula.

The role of poroelastic diffusion in the transient wetting behavior of hydrogels.

Wetting and water absorption of hydrogels is often encountered in many applications. We seek to understand how wetting behavior can be affected by the time-dependent swelling of hydrogels. We measured the advancing contact angles of water droplets on hydrogels of varying thicknesses where thicker gels absorbed water more slowly. We also observed that, above a threshold advancing speed, water droplets would collapse into a lower contact angle state on the surface. We hypothesized that this collapse threshold speed is a result of competition between the poroelastic diffusion of water into the gel and the advance of the spreading droplet, the thickness of the surface, and the diffusion of water into the gel. Taking the ratio of the diffusion and advancing timescales results in a Peclet number with gel thickness as a characteristic length scale. Our results show that above a Peclet number of around 40, droplets will collapse on the surface across all gel thicknesses, confirming our hypothesis. This work provides simple insight to understand a complex time-dependent wetting phenomenon for a widely used hydrogel.

Eco-friendly approach for the fabrication of biо copper based superhydrophobic coating on steel metal and its corrosion resistance evaluation

This study presents an eco-friendly approach for constructing superhydrophobic (S.H.) coatings on steel surfaces. The biо Сu nanoparticles are synthesized using a biоgenic process. Two types of coatings, Ni-Ѕ.Α and Ni-biо Сu-Ѕ.Α, were developed and characterized. The EDX results confirm the successful fabrication of two distinct coatings on the steel substrate: one involving the modification of nickel with stearic acid, Ni-Ѕ.Α, and the other involving the modification of nickel with both bio-Cu and stearic acid, Ni-biо Сu-Ѕ.Α. The SEM results revealed that the S.H. coats exhibit circular microstructures which contribute to the surface roughness. The contact angles of water droplets on the Ni-Ѕ.Α and Ni-biо Сu-Ѕ.Α coatings were measured at 158° ± 0.9° and 162° ± 1.1°, respectively. Chemical stability tests demonstrated that the Ni-Ѕ.Α coating maintains its S.H. behaviour in a pH range of 3–11, whereas the Ni-biо Сu-Ѕ.Α coating exhibits excellent chemical stability in a broader range of pH (1-13). The coating's mechanical stability was evaluated through abrasion tests. The Ni-Ѕ.Α coating retained its S.H. properties even after an abrasion length equal 1100 mm, while the Ni-biо Сu-Ѕ.Α coating maintained its S.H. behaviour till an abrasion length equal 1900 mm. The corrosion behavior and protective properties of the S.H. coatings were studied via electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization (PDP) techniques. The PDP and EIS findings demonstrated that both Ni-Ѕ.Α and Ni-biо Сu-Ѕ.Α coatings significantly reduced the corrosion rate compared to uncoated steel.

Effects of the etching process on the surface, friction and wear characteristics of silicone rubber coated with micro-sized ceramic particles.

This study investigates the friction and wear characteristics of silicone rubber used in hydraulic systems, focusing on surface properties achieved through coating strategies. Silicone rubber specimens with varying surface characteristics, prepared by coating with micro-sized ceramic particles and employing etching processes, were examined. Surface morphology, roughness, water droplet contact angles, and friction and wear characteristics were evaluated. The silicone rubber was coated with ceramic particles (average size: 16 μm) and subsequently etched for different durations (1, 5, 10, 30, and 60 minutes). The results revealed that longer etching times led to increased surface roughness, while shorter etching times resulted in improved wear characteristics. The friction coefficient demonstrated a discernible reduction with escalating etching durations, with Etching-60M showing approximately 50% lower friction coefficient compared to Etching-1M. Wear rates ranged from 2.47 × 10-7 to 1.43 × 10-6 mm3 N-1 mm-1, indicating an increasing trend with longer etching times. Distinct wear mechanisms were observed between non-etched and etched specimens, with the latter exhibiting more pronounced wear tracks. Finite element analysis highlighted variations in stress behavior during contact sliding, indicating that surface modifications significantly impact wear resistance. While longer etching times improved friction characteristics, shorter etching times yielded superior wear characteristics. Further research is recommended to explore optimal etching conditions considering various variables.

Influence of surface texture of electric discharge machined Ti6Al4V on the surface wettability

This study examines the effects of crucial ISO 25178 parameters, including height, functional, spatial, functional (stratified), hybrid, and functional (volume), on surface wettability and the influence of key electric discharge texturing process parameters, including current and pulse ON time, on surface roughness (Sa) and water droplet contact angle. To examine the level of significance of each parameter and to determine the level of correlation, a three-level full factorial experimental design, and ANOVA analysis are used. The findings showed that over pulse ON time, the important factor influencing surface roughness (Sa) and contact angle is current. The surface roughness (Sa) is observed to vary between 4.2 and 12.7, whereas the water droplet contact angle varies between 90.7° and 120.4°. In order to find out the correlation between the surface texture parameters based on the ISO 251718, Pearson Correlation analysis were adopted and it is observed that Sa, Sq, Str, Smrk1, Sdr, Vm, and Vmp are having a substantial correlation with the contact angle. Among the ISO25178 parameters examined, Smrk1, however, has demonstrated a highest impact on the contact angle with a highest pearson correlation coefficient of −0.757.

Preparation and properties of a simple super‐hydrophobic carbon fiber composite surface

AbstractSuper‐hydrophobic surface is widely used in waterproof, antifouling, and anticorrosion fields because of its unique wetting characteristics. However, the rough structure of super‐hydrophobic surface is easily damaged in service, which leads to the loss of various properties, making it difficult to apply super‐hydrophobic surface on a large scale in actual production. In this paper, epoxy resin was used as adhesive, mixed with hydrophobic silica particles and sprayed on the surface of carbon fiber composites. After curing, the surface of super‐hydrophobic carbon fiber composites with contact angle of 158 ± 2° and sliding angle of 1 ± 0.5° was formed. The surface had excellent dynamic water repellent performance, and the droplets could bounce more than three times on the surface. Furthermore, the super‐hydrophobic surface had excellent wear resistance and mechanical stability. After the friction damage test, the surface structure of the sample was slightly damaged. The amount of wear was small, and the surface was still in super‐hydrophobic state. Through soaked in solutions with different pH values, the microstructure of the surface was not obviously damaged by corrosion, the contact angle of water droplets was greater than 155°. The preparation method of super‐hydrophobic surface of carbon fiber composite proposed in this study is simple and rapid, and the prepared surface has excellent performance, the practical application of super‐hydrophobic surface is promoted.

Enhancing the Efficiency of Ice-Resistant Materials in Asphalt Road Surfaces: A Comprehensive Performance Analysis

This study addresses the critical issue of traffic safety in winter, particularly focusing on the challenges posed by ice and snow on roads. Traditional methods of snow and ice removal are often labor-intensive, inefficient, and environmentally harmful. The objective is to develop a more effective solution for asphalt pavement deicing. Inspired by the anti-icing coating technology used in high-voltage conductors, this research develops an ice-suppressing material designed to reduce the adhesion between snow, ice, and pavement surfaces. The material’s performance is evaluated in terms of deicing efficiency, durability, adhesive properties, and its impact on pavement performance. Test results demonstrate that the developed ice-suppressing material significantly reduces the adhesion between the ice layer and the pavement, facilitating easier removal. This study concludes that the developed ice-suppressing material significantly enhances deicing efficiency on asphalt pavements. It exhibits strong hydrophobic properties, as evidenced by increased water droplet contact angles on coated surfaces (99.5° to 83.3°) compared to clean glass slides (39.2° to 29°). This hydrophobicity effectively reduces ice adhesion, decreasing tensile and shear strength of the ice layer by 38.2% and 63.6%, respectively. Additionally, the material demonstrates superior ice-melting capabilities in sub-zero temperatures, with coated ice cubes showing a higher mass reduction rate than uncoated ones. Importantly, its slow-release nature ensures sustained deicing performance over multiple cycles, maintaining effectiveness after seven test cycles. This study introduces an innovative ice-suppressing material that not only improves the efficiency and environmental impact of deicing methods but also contributes to enhancing road safety in winter conditions. The material’s novel composition and sustained effectiveness present a significant advancement in the field of winter road maintenance.

Influence of the Porphyrin Structures on the Contact Angle of Water Wetting by Langmuir-Schaefer Films

Studying the contact angle of water droplets on the surfaces of thin films formed by organic compounds allows to establish hydrophilic/hydrophobic properties of the films. Knowledge of hydrophilicity/hydrophobicity makes it possible to optimize the composition and increase the adhesive properties of films, improving their functionality. In this study, the dependence of the contact angle of Langmuir-Schaefer films (LS-films) of three compounds: 5,10,15,20-tetraphenylporphyrin (I), 2-aza-21-carba-5,10,15,20-tetraphenyl-porphyrin (II), and 5,15-bis(2,6-bis(dodecycloxy)phenyl)porphyrin (III) was examined. Contact angle data were obtained for LS-films with different transfer numbers of floating layers of the studied porphyrins and different surface roughness. It was found that LS-films of compounds I and II are hydrophobic and their hydrophobicity increases with an increasing of transfer number. In addition, an increase in the surface roughness of the LS film of compound I compared to compound II reduces the value of the contact angle. Unlike porphyrins I and II, LS-films of compound III displayed hydrophilic properties. The obtained data can be used for the targeted design of compounds to create thin film materials of various purposes.

Optimization of Manufacturing Parameters for Fluorinated Ethylene Propylene (FEP)/Graphene Hydrophobic Coatings

The coating of surfaces carrying fluid with hydrophobic materials has shown effective results in reducing friction factors. In this study, the optimization of manufacturing parameters, including the additive ratio, curing temperature, and curing time was conducted to enhance the hydrophobic behavior of fluorinated ethylene propylene (FEP) material by incorporating nano graphene additives. Three different levels for the optimized parameters were determined based on the literature sources. These levels were set as 1% wt, 2% wt, and 3% wt for graphene additive ratios, 200 ˚C, 300 ˚C, and 400 ˚C for curing temperatures, and 30 min, 40 min, and 50 min for curing times. Following the L9 Taguchi design, the FEP/graphene mixture was applied to AISI 304 stainless steel surfaces, and the curing process was completed in an oven. The optimization process was performed based on the response of water droplet contact angles on the surfaces. The optimum graphene additive ratio was determined as 1%, the optimum curing temperature was 400 ˚C, and the optimum curing time was found to be 40 min. Variance analysis revealed that the curing temperature had the most significant effect on the contact angles with a contribution rate of 96.78%. Applying the optimal manufacturing parameters to the FEP coating material with added additives can contribute to energy savings in applications such as pumps, turbines, and pipelines.